Column Sizing Calculator
How to use: Select a resin preset or enter your DBC and product mass per batch. The calculator sizes production columns, compares candidate diameters, and estimates buffer consumption and cycle times.
Resin / Application Preset
Product Mass per Batch (g) ?
DBC at 10% Breakthrough (g/L resin) ?
Load Factor (%) ?
Target Bed Height (cm) ?
Recommended Linear Velocity (cm/h) ?
Resin Cost ($/L) ?
Buffer Volumes per Cycle (CV)
Equilibration
Wash
Elution
Strip
CIP
Re-equil.
0.0
L resin required
Minimum Resin Volume
--
Cycles / Batch
--
Buffer / Batch (L)
--
Process Time (h)
--
Resin Cost ($)
Candidate Column Comparison
Diameter (cm)Vol (L)CyclesBuffer/Batch (L)Time (h)Resin Cost ($)
Buffer Consumption per Cycle
Cycles vs Column Diameter
Want to optimise your chromatography binding and elution conditions? Design a screening experiment with DOE

Related Articles

Chromatography Resin Selection Guide
How to choose the right resin for your process
Column Packing and Qualification
HETP, asymmetry and packing best practice
Chromatography Step Calculator
Residence time, DBC, linear velocity and load ratio
Resin Lifetime Calculator
DBC decay modelling and resin replacement planning

Further Reading

Frequently Asked Questions

How do I size a chromatography column for production scale?

Start with small-scale loading studies to determine the dynamic binding capacity (DBC) at 10% breakthrough. Then calculate the required resin volume as product mass per batch divided by (DBC times the load factor, typically 80%). Choose a standard column diameter and bed height that gives this volume, keeping bed height within the resin manufacturer's recommended range (typically 15-30 cm).

What is the difference between constant residence time and constant linear velocity scale-up?

Constant residence time maintains the same contact time between product and resin at both scales, preserving binding kinetics and selectivity. Constant linear velocity maintains the same flow speed through the packed bed, preserving pressure drop and mass transfer characteristics. In practice, constant residence time is preferred for bind-and-elute steps, while constant linear velocity is preferred for flow-through polishing steps.

How many column volumes of buffer are needed per cycle?

A typical mAb Protein A cycle uses 15-25 column volumes (CV) total: 3-5 CV equilibration, variable load volume, 3-5 CV wash, 3-5 CV elution, 2-3 CV strip, and 3-5 CV CIP. Ion exchange and polishing steps may use more or fewer CVs depending on gradient length and regeneration requirements.

What is the typical DBC for Protein A resins?

Modern Protein A resins typically achieve 35-65 g/L DBC at 10% breakthrough with a 4-6 minute residence time. MabSelect SuRe achieves approximately 35 g/L, MabSelect PrismA 55-65 g/L, and Toyopearl AF-rProtein A-650F approximately 40 g/L. DBC depends on feed concentration, residence time, and the specific antibody.

How do I calculate the number of cycles per batch?

Divide the total product mass per batch by the mass loaded per cycle. The mass per cycle equals DBC multiplied by the resin volume multiplied by the load factor (typically 0.7-0.85). Round up to the nearest whole number. Fewer cycles means less processing time but requires a larger (more expensive) column.

What standard column diameters are available?

Standard process column diameters range from 1 cm (lab scale) through 2.6, 4.4, 7.1, 10, 14, 20, 30, 45, 63, 80, 100, 140, and 200 cm (manufacturing scale). Common lab-to-pilot columns include XK 16 (1.6 cm), XK 26 (2.6 cm), and XK 50 (5 cm). Production columns include BPG, AxiChrom, and similar formats.